Hoefer GD2000 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Hoefer GD2000. Hoefer GD2000 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer

Résumé du contenu

Page 1 - Slab Gel Dryer

user manualum    GD2000-IM/Rev.B0/07-12GD2000 Slab Gel DryerVacuum Gel Dryer System

Page 2 - Contents

Design FeaturesDrying  surfaceThe PTFE coated, cast aluminum platen is resis-tant to acidic fumes that may be released while drying certain types of g

Page 3 - Vigtig Information – Danish

• p32. Unpacking the GD2000Carefully unwrap all packages and compare the items received with the packing list, making sure all items arrived. If any p

Page 4 - Tärkeää Tietoa – Finnish

Setting Up  the Vacuum SystemThe vacuum system must include a vacuum pump capable of moving an air volume of at least 1.5 m3/h, but not more than 6 m3

Page 5

Gel dryer  controlsThe GD2000 control panel is located on the top of the gel dryer. (See Fig 1). A detailed view of the features of the control panel

Page 6 - Portuguese

• p6number  control feature  function 1 LED display Shows Set Temperature, Set Time or Elapsed Time. On the left of the LED display, a light indi

Page 7 - Viktig Information – Swedish

3. Spécifications Maximum Operating RatingsWattage Heater: 800 W, thermostatically controlled Pump Outlet 575 WPower requirements Model: 80-642

Page 8 - Electronic Equipment (WEEE)

4. Operating instructionsAfter you have attached the vacuum pump to the GD2000, follow these instructions to prepare the dryer and gel drying stack. O

Page 9 - 1. Gel Dryer function and 

Step 2:  Prepare the gel drying stackThe slab dryer accommodates both agarose and polyacrylamide gels. The configuration of the gel stack layers depend

Page 10 - Design Features

Drying  thin or low-concentration polyacrylamide gels  (≤ 1.5 mm) and  agarose gels on paper1Lay a sheet of filter paper on top of the filter paper line

Page 11 - 2. Unpacking the GD2000

Drying  thick gels (> 1.5 mm), high concentration gels,  gradient gels on paper1Lay a sheet of filter paper on top of the filter paper liner and then

Page 12 - Setting Up  the Vacuum System

• piContents Important Information ... iiWaste Electrical and Electronic Equipment (WEEE) ...

Page 13 - Gel dryer  controls

• p12Step 3:  Set the temperatureThe highest setting, 80 °C, can be used for many types of gels for reliable, rapid drying. Use a temperature of 50 °C

Page 14

• p13Step 4:  Set the timerThe amount of time required for a gel to dry depends on such factors as gel thickness, gel concentration, drying temperatur

Page 15 - 3. Spécifications

• p14To start the heater and the vacuum pump• You can press the Time/Temp key to immedi-ately start the heater and vacuum pump.• If you don’t press

Page 16 - 4. Operating instructions

• p15Step 5:  Create a vacuum sealTen seconds after you set the timer, the vacuum starts automatically if it is connected through the vacuum receptacl

Page 17 - *not used with agarose gels

• p16Options for  manual operationsTo apply a vacuum without heat. Set the Temperature to 0:FF, then set the timer. Ten seconds after you set the time

Page 18

• p175. Care and maintenanceCleaning1Turn mains power switch off and unplug the power cord.2Remove the stainless steel screen and cover sheets and wa

Page 19 - Fig 5. Stacks for drying

• p18Replacing fuses115 V~ Model. The fuse drawer holds one F 12A 250V 3AG fuse and one shorting coil.230 V~ Model. The fuse drawer holds two F 6.3A 2

Page 20 - Step 3:  Set the temperature

• p19Replacing the  rubber sealing sheetOccasionally, a tear or nick in the rubber sealing sheet (SE1143) may inhibit the formation of the vacuum seal

Page 21 - Step 4:  Set the timer

• p206. Troubleshootingproblem  solutionNo power or LED Display Check that the power switch is turned on. Check that the dryer is plugged into a wor

Page 22

• p217. Ordering information product  quantity  code numberGD2000 Vacuum Gel Dryer System Includes: stainless steel screen, VP200 Vacuum pump, Vacu

Page 23 - Step 6:  Disassembly

• piiImportant Information  – English• If this equipment is used in a manner not specied by Hoefer, Inc. the protection provided by the equipment ma

Page 24

Hoefer, Inc. 84 October Hill Road Holliston, MA 01746Toll Free: 1-800-227-4750 Phone: 1-508-893-8999 Fax: 1-508-893-0176 E-mail: [email protected]

Page 25 - 5. Care and maintenance

• piii80%). Undgå kondensation ved lade enheden equili-brate til omgivende temperatur ved tageen instru-mentets fra et koldere til et varmere miljø. •

Page 26 - Replacing fuses

• pivil devrait être seulement utilisé par les opérateurs convenablement entraînés. Lire ce manuel entier avant utiliser l’instrument et l’usage seule

Page 27

• pvl’unità equilibra alla temperatura ambiente quando portare lo strumento da un più freddo a un ambiente più caldo. • Di permettere rareddare suc

Page 28 - 6. Troubleshooting

• pvisuaoperação. • Este instrumento é projectado de acordo com o EN61010-1:2001 condição de segurança eléctrica. Não obstante, deve ser usado só po

Page 29 - 7. Ordering information

• pviiEnglishFrenchGermanItalianSpanishSwedishThis symbol indicates that the waste of electrical and electronic equipment must not be disposed as unso

Page 30

1. Gel Dryer function and descriptionThe Hoefer® GD2000 Slab Gel dryer rapidly dries acrylamide and agarose gels and perma-nently bonds them to filter

Commentaires sur ces manuels

Pas de commentaire